How to open a Mosler safe with combination?

Pete C.

2012-01-20 13:40:04 UTC

Post by Ignoramus32441
I purchased this Mosler safe. As you can see, it is open and empty, so
http://igor.chudov.com/tmp/Mosler-Safe/
The combination, as written on the masking tape stuck on the safe,
R 63
L 47 3 turns
R 25 2 turns
L to 0
However, the safe would not open. I was once shown that the combo
works, however, I cannot redo it. The safe is still open and I would
like to figure it out.
If anyone can help me, it will be GREATLY appreciated!
Thanks, guys!
i

Where are you starting from? I think you may need to spin it L a couple
turns to line all the disks up at the starting point before the first R
63.

Steve W.

2012-01-20 13:52:37 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.

Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Ignoramus32441

2012-01-20 14:42:56 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11

Thanks!

i

Bob La Londe

2012-01-20 17:04:00 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

Ignoramus32441

2012-01-20 18:04:52 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).

i

tnik

2012-01-20 18:17:34 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

Aye, but look at it this way.. We now have a head start on figuring out
the real numbers now.

Tom

Ignoramus32441

2012-01-20 18:21:10 UTC

Post by tnik

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

Aye, but look at it this way.. We now have a head start on figuring out
the real numbers now.
Tom

There is an automated CNC machinegun pointed right at the safe.,

i

azotic

2012-01-20 18:43:52 UTC

--
http://fija.org/

Post by tnik

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

Aye, but look at it this way.. We now have a head start on figuring out
the real numbers now.
Tom

There is an automated CNC machinegun pointed right at the safe.,
i

Fortunatley for criminals machineguns are banned in illinios.

Best Regards
Tom.

--
http://fija.org/

Leon Fisk

2012-01-20 19:38:59 UTC

On Fri, 20 Jan 2012 12:21:10 -0600

Post by tnik
Aye, but look at it this way.. We now have a head start on figuring out
the real numbers now.
Tom

There is an automated CNC machinegun pointed right at the safe.,

Maybe you have seen it already...

There is an old Clint Eastwood movie from 1974 called "Thunderbolt and
Lightfoot":

http://www.imdb.com/title/tt0072288/

They used a rather interesting way of opening/getting into the bank
vault. Didn't have the action, special effects like nowadays, but I
rather enjoyed it :)

--
Leon Fisk
Grand Rapids MI/Zone 5b
Remove no.spam for email

fred

2012-01-20 22:36:20 UTC

Post by Leon Fisk
Maybe you have seen it already...
There is an old Clint Eastwood movie from 1974 called "Thunderbolt and
http://www.imdb.com/title/tt0072288/
They used a rather interesting way of opening/getting into the bank
vault. Didn't have the action, special effects like nowadays, but I
rather enjoyed it :)

A movie classic IMO although I'm sure redneck america will object to
Jeff Bridges' short lived appearance in tights.

--
fred
it's a ba-na-na . . . .

Stormin Mormon

2012-01-21 03:15:51 UTC

I saw that movie, ages ago. It was a real blast.

Christopher A. Young
Learn more about Jesus
www.lds.org
.

Post by Leon Fisk
http://www.imdb.com/title/tt0072288/
They used a rather interesting way of opening/getting into the bank
vault. Didn't have the action, special effects like nowadays, but I
rather enjoyed it :)

A movie classic IMO although I'm sure redneck america will object to
Jeff Bridges' short lived appearance in tights.

--
fred
it's a ba-na-na . . . .

Michael A. Terrell

2012-01-31 05:17:06 UTC

Post by Ignoramus32441
There is an automated CNC machinegun pointed right at the safe.,

BULLSHIT!!!

If there was, you would have had at least seven threads here asking
what kind of gun:
1: How to mount it.
2: What gauge of wire to use.
3: Whether you should use a servo, solenoid or stepper motor. This would
spawn multiple sub threads, as well.
4: What metal to make the mount with.
5: Where to get the cheapest bullets.
6: How to make it self destruct before the police arrive.
7: How to explain why someone broke into your building and shot
themselves several hundred times, along with all the damage to the safe.

--
You can't have a sense of humor, if you have no sense.

Ignoramus18027

2012-01-31 05:25:09 UTC

Post by Michael A. Terrell

Post by Ignoramus32441
There is an automated CNC machinegun pointed right at the safe.,

BULLSHIT!!!
If there was, you would have had at least seven threads here asking
1: How to mount it.
2: What gauge of wire to use.
3: Whether you should use a servo, solenoid or stepper motor. This would
spawn multiple sub threads, as well.
4: What metal to make the mount with.
5: Where to get the cheapest bullets.
6: How to make it self destruct before the police arrive.
7: How to explain why someone broke into your building and shot
themselves several hundred times, along with all the damage to the safe.

Very funny, good job.

i

Jon Elson

2012-01-20 20:47:04 UTC

Post by Ignoramus32441
It would be especially handy if I provided actual numbers (see my
first post).

As Richard Feynman showed, a 3-digit safe can be unlocked in minutes
even if you don't know even one digit of the combination. 5-number
combo safes take a little longer, he could usually get them open in
an hour!

Jon

Ignoramus32441

2012-01-20 22:37:55 UTC

Post by Jon Elson

Post by Ignoramus32441
It would be especially handy if I provided actual numbers (see my
first post).

Not under fire of my CNC machinegun...

Plus, one try of this safe takes, I would say, at least 30 seconds.

i

j***@gmail.com

2016-02-23 01:23:38 UTC

I have a safe with the combo and im trying to open it and I can't get it. It's so old. Can someone please help? Thank you:)

Jay Hennigan

2016-02-23 03:18:47 UTC

Post by j***@gmail.com
I have a safe with the combo and im trying to open it and I can't get it. It's so old. Can someone please help? Thank you:)

Turn the dial to the left at least four complete revolutions.

Stop at the first number of the combination.

Turn to the right and stop on the second number the THIRD time it appears.

Turn to the left and stop on the third number the SECOND time it appears.

Turn to the right and stop on zero. If there is a small inner knob in
the middle of the dial turn it all the way to the right. Then continue
turning the dial to the right until it stops.

If no small inner knob, then turn the dial to the right until it stops.
Open the safe.

1***@gmail.com

2016-02-28 00:45:51 UTC

Post by Jay Hennigan

Post by j***@gmail.com
I have a safe with the combo and im trying to open it and I can't get it. It's so old. Can someone please help? Thank you:)

Turn the dial to the left at least four complete revolutions.
Stop at the first number of the combination.
Turn to the right and stop on the second number the THIRD time it appears.
Turn to the left and stop on the third number the SECOND time it appears.
Turn to the right and stop on zero. If there is a small inner knob in
the middle of the dial turn it all the way to the right. Then continue
turning the dial to the right until it stops.
If no small inner knob, then turn the dial to the right until it stops.
Open the safe.

Pete C.

2012-01-20 19:39:58 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

Who needs numbers? We'll just use your plasma cutter... :)

Steve W.

2012-01-20 22:25:38 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

It isn't that hard to change those IF you needed to (I would since the
original owner knows the current combination)
You need the correct change key and the correct directions. Or just pay
a smith to change it.

Steve W.

Ignoramus32441

2012-01-20 22:38:24 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

OK, how much would it cost? Very interesting.

i

Steve W.

2012-01-21 00:12:59 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

OK, how much would it cost? Very interesting.
i

Depends on the local market. Around here the usual charge runs about $75.00
If you have the key DIY isn't hard.

Diebold provides service for them.

--
Steve W.

Ignoramus32441

2012-01-21 01:00:12 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

OK, how much would it cost? Very interesting.
i

Depends on the local market. Around here the usual charge runs about $75.00
If you have the key DIY isn't hard.
Diebold provides service for them.

Thanks. I will definitely consider it.

I am also thinking, what should I do with this safe, in the sense of
bolting it down. How is that properly done. It weighs only about 600
lbs and is in a place with pallet jacks and forklifts. Someone could
just forklift it out of there.

Just to be clear, I am not anticipating storing any high value stuff
in there, but I like to do things the right way, so I want to know how
are safes properly secured.

Now, regarding key: the safe has a key hole in the lock. I do not have
that key, and the safe seems to open and close without the need for
any key. So, what is the purpose of that key? For changing
combination? Is that what you were referring to?

Thanks

i

Steve W.

2012-01-21 01:37:03 UTC

Post by Ignoramus32441
Thanks. I will definitely consider it.
I am also thinking, what should I do with this safe, in the sense of
bolting it down. How is that properly done. It weighs only about 600
lbs and is in a place with pallet jacks and forklifts. Someone could
just forklift it out of there.
Just to be clear, I am not anticipating storing any high value stuff
in there, but I like to do things the right way, so I want to know how
are safes properly secured.
Now, regarding key: the safe has a key hole in the lock. I do not have
that key, and the safe seems to open and close without the need for
any key. So, what is the purpose of that key? For changing
combination? Is that what you were referring to?
Thanks
i

The key is to change the combination, and depending on the model it can
be set up to open the safe as well.

As to securing it. Figure out where you want it. Make a template of the
hole pattern in the base. then drill holes and use anchors to secure it
to the floor.

If you were doing new construction you would do a bit more, like install
hardened J bolts in the concrete, install ceramic/steel sleeves over
them. Bolt the safe down and then tack the nuts in place. Then float
concrete in around the base as well. Some do even more like adding
plates below the safe and walling it in with steel/ceramic/steel
composite plates.

--
Steve W.

Pete C.

2012-01-21 02:32:11 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

OK, how much would it cost? Very interesting.
i

Depends on the local market. Around here the usual charge runs about $75.00
If you have the key DIY isn't hard.
Diebold provides service for them.

Thanks. I will definitely consider it.
I am also thinking, what should I do with this safe, in the sense of
bolting it down. How is that properly done. It weighs only about 600
lbs and is in a place with pallet jacks and forklifts. Someone could
just forklift it out of there.
Just to be clear, I am not anticipating storing any high value stuff
in there, but I like to do things the right way, so I want to know how
are safes properly secured.
Now, regarding key: the safe has a key hole in the lock. I do not have
that key, and the safe seems to open and close without the need for
any key. So, what is the purpose of that key? For changing
combination? Is that what you were referring to?
Thanks
i

When anchoring things to concrete, think Hilti. The wedge type anchors
are good as are the threaded insert type, you can't remove either type,
but you can fill them in or grind them flush if you remove the safe
later. FYI after the Boston tunnel started dropping ceiling slabs and
killing people, they called in Hilti to secure the ceiling panels
properly.

Evan

2012-01-21 20:11:16 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

I better write that down in case I am ever in Illinois. It might come in
handy. LOL.

It would be especially handy if I provided actual numbers (see my
first post).
i

OK, how much would it cost? Very interesting.
i

Depends on the local market. Around here the usual charge runs about $75.00
If you have the key DIY isn't hard.
Diebold provides service for them.

Thanks. I will definitely consider it.
I am also thinking, what should I do with this safe, in the sense of
bolting it down. How is that properly done. It weighs only about 600
lbs and is in a place with pallet jacks and forklifts. Someone could
just forklift it out of there.
Just to be clear, I am not anticipating storing any high value stuff
in there, but I like to do things the right way, so I want to know how
are safes properly secured.
Now, regarding key: the safe has a key hole in the lock. I do not have
that key, and the safe seems to open and close without the need for
any key. So, what is the purpose of that key? For changing
combination? Is that what you were referring to?
Thanks
i

The change key hole is inside the safe on the inner surface
of the lock case... That is what you need if you want to
change the combination of the lock...

If you are referring to a keyhole in the dial, that is to lock
the dial so that without the key it won't be engaged to
spindle to prevent someone from casually playing
around with it... It doesn't and won't stop someone
who knows what they are doing as far as safe cracking...

~~ Evan

Ignoramus1414

2012-01-22 00:14:04 UTC

Post by Evan
If you are referring to a keyhole in the dial, that is to lock
the dial so that without the key it won't be engaged to
spindle to prevent someone from casually playing
around with it... It doesn't and won't stop someone
who knows what they are doing as far as safe cracking...

The key hole that I was referring to, is not in the dial, it is in the
handle that opens the lock once the dial is correctly dialed.

I thought that there are very few truly professional criminal
safecrackers left nowadays, unlike, say, in 1920's or some such.
The prosession sort of died out, kind like pike pickpockets are dying
out due to "cashless economy".

Is that right or wrong?

i

Evan

2012-01-22 03:11:41 UTC

Post by Ignoramus1414

The key hole that I was referring to, is not in the dial, it is in the
handle that opens the lock once the dial is correctly dialed.
I thought that there are very few truly professional criminal
safecrackers left nowadays, unlike, say, in 1920's or some such.
The prosession sort of died out, kind like pike pickpockets are dying
out due to "cashless economy".
Is that right or wrong?
i

Such a keyhole in the handle is a secondary means of security
when the main lock is secured, it also needs to be open for
the safe to open... It can also be used as a "day lock" for
securing the safe between uses without having to dial the
combination in each and every time... Look at how a "day gate"
is used on a bank vault so that the main vault lock does not
have to be operated every time someone needs access to
the vault...

Very very wrong...

Why do you think safe designers keep improving the materials
and mechanics/mechanisms used to secure the contents of
safes...

In the 1920's fun technology like plasma cutters didn't exist
which would cut through an old safe like a knife through
warm butter... In the olden days safes used to use chemical
warfare like tear gas cylinders and such in the doors to
deter people from drilling or blasting them open...

As far as pickpockets being a dying breed you are sounding
like you are not from anywhere near a big city, pickpockets
still exist and still lift wallets and other things from pockets,
backpacks and purses that are wallet sized like cell phones,
iPods and such... A wallet in a "cashless society" is often
worth quite a bit more than a wad of cash in the first few
hours after it is stolen yet before the owner can report all
the stolen cards to each bank because basically no one
keeps a list of all that information handy and the person
has to go home to get all the account numbers and call
customer service from the numbers on the account
statements...

Identity theft is something on the order of a $40 Billion
with a B dollar a year "industry" in the United States
alone...

~~ Evan

DoN. Nichols

2012-01-22 05:02:59 UTC

[ ... ]

Post by Evan

Post by Ignoramus32441
Now, regarding key: the safe has a key hole in the lock. I do not have
that key, and the safe seems to open and close without the need for
any key. So, what is the purpose of that key? For changing
combination? Is that what you were referring to?

[ ... ]

Post by Evan
The change key hole is inside the safe on the inner surface
of the lock case... That is what you need if you want to
change the combination of the lock...

I believe that this combination lock (based on the photo of the
front panel of the safe -- actually a security file cabinet) is of the
kind where you disassemble it, and change the relation between the hub
and the outer disc (where the notch is to allow opening when all are
lined up). It also does not have the tumbler in the middle of the
combination dial to switch from dialing mode to the retract the bolt
mode. So this one would not have a change key, unlike the Sargent &
Greenleaf ones. (It is a vintage device, FWIW.)

No -- the keyhole in question is not in the dial, nor in the
back of the lock (which was not shown in the photos linked in the
original question). Instead, it is in the center of another section to
the left of the actual combination dial. This section is what withdraws
the bolts in the door -- when allowed by the combination lock having
been properly dialed. And the key simply keeps the withdrawal lever
(actually two wings on either side of the keyhole) from turning -- or
totally disconnects it from the bolt withdrawal mechanism. Without my
hands on the device in question, and considering the one which I had was
left behind in the apartment storage room about 1975, I can't check it. :-)

But it, like this one, has the door designed to slide back on
tracks into a cavity beside the actual file cabinet, so it is out of the
way during normal daytime access to its contents -- at the cost of the
whole thing being a little wider than the more common Diebold security
file cabinets which were at work before I retired.

Enjoy,
DoN.

--
Remove oil spill source from e-mail
Email: <***@d-and-d.com> | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---

RS at work

2012-01-24 06:42:44 UTC

The key locking dial has several functions intended, but this is the
first I have heard of the casual play theory.

the first function is to day lock the safe. This is used when some
one is in and out of the safe all day long and wants to keep it
locked, but does not want to re-dial the combo each time.

A secondary use is on a drop safe serviced by an armored car company.
The merchant has the combination to the dial on the drop side of the
safe but is not issued the key, so the cash stays secured in the event
of a hold-up.

Roger Shoaf

Stormin Mormon

2012-01-21 03:15:05 UTC

It's very wise to get some training first. It's far too easy to mess things
up, and lock yourself out.

Christopher A. Young
Learn more about Jesus
www.lds.org
.

"Steve W." <***@NOTyahoo.com> wrote in message news:jfcpl6$prl$***@dont-email.me...

It isn't that hard to change those IF you needed to (I would since the
original owner knows the current combination)
You need the correct change key and the correct directions. Or just pay
a smith to change it.

Steve W.

Jay Hennigan

2021-12-29 07:24:09 UTC

I have a 60s era mosler gsa or cia safe with an S&G lock mechanism with no
hole in the back cover for a change key and no 2nd index mark on the dial.
Can the combo be changed?

Yes, but I'd recommend taking it to a professional. It's what's called
a hand change lock. Inside the case are wheels, sort of like gears,
that can be aligned in different ways to set the combination. I advise
a professional because it's a precision mechanism with many small
parts, and also there are certain combinations that should not be used
due to mechanical limitations, called the forbidden zone. Lock and safe
technicians are familiar with all of this.

This type of work is much cheaper if you take the safe, the door, or
the lock to the locksmith rather than having them come to you. Look for
a brick-and-mortar local locksmith that works on safes and vaults,
ideally an old-school establishment.

pyotr filipivich

2012-01-20 18:52:03 UTC

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11

Keep it in a secure place.

Just don't store that note _in the safe_.

Just saying.
--
pyotr
Go not to the Net for answers, for it will tell you Yes and no. And
you are a bloody fool, only an ignorant cretin would even ask the
question, forty two, 47, the second door, and how many blonde lawyers
does it take to change a lightbulb.

Martin Eastburn

2012-01-21 04:08:53 UTC

The note might be a pig Latin note of sorts - written
in reverse to fake out the bad guys but easy for the rightest!

Martin

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Steve W, your instruction was 100% on target! The safe now opens!!! I
will save the exact instructions for the future, I am VERY VERY
HAPPY!!!!!!!!!!!!!!11
Thanks!
i

karlawilliams4@yahoo.com

2018-04-16 13:03:41 UTC

Hello-
I was wondering if you could recommend anyone in Indianapolis, IN who could open a Mosler safe.
It is part of my father's estate and we do not have the combination.
It is a Big steal blue safe, about 4x2x3.
I have not found any specific numbers on it to identify it better.
Any input on how to proceed would be a great help.
Thank you so much!
Karla

Derek Broestler

2018-04-18 15:51:53 UTC

Post by ***@yahoo.com
Hello-
I was wondering if you could recommend anyone in Indianapolis, IN who could open a Mosler safe.
It is part of my father's estate and we do not have the combination.
It is a Big steal blue safe, about 4x2x3.
I have not found any specific numbers on it to identify it better.
Any input on how to proceed would be a great help.
Thank you so much!
Karla

My best advice would be to find a SAVTA (Safe And Vault Technicians Association) certified safe technician through the SAVTA website http://www.savta.org/savta_tech.php you can enter you zip code and find someone qualified and local. For a city the size of Indianapolis you should have a few to pick from...

Jeff Kiral

2019-10-13 02:03:17 UTC

Yes but you are going to need the help of a locksmith that does safe work. If the safe is open, it will not be too difficult. If the safe is closed, it will need opened first. A locksmith that does safe work should also be able to get the original combination for you.

b***@gmail.com

2020-01-12 17:00:32 UTC

Read this 8 years later and it SAVED me. Thank you!

Mosler usually has a set number of turns on the first number as well.
Plus the directions shown look backwards.
Try Left 4 turns to 63, Right 3 turns to 47, Left 2 turns to 25 then
right 1 turn to 0 continue turning to the right till the dial stops and
you can open the safe.

Doug White

2012-01-20 14:14:03 UTC

The "turns" can be a bit misleading. I have had to deal with dozens of
different flavors of locks over the years, and here is how MOST of them
work:

Start by turning the dial clockwise (R) 3 or 4 times to get everything
engaged internally. Stop at 63.

Turn the dial counterclockwise past 63 twice and stop at 47.

Turn the dial clockwise past 47 once, and stop at 25.

Turn the dial counterclockwise to 0.

Here's where it can get tricky. Some locks will just open at this point.
Some of them you can feel something going on internally as the mechanism
drops into place, and then you can open it. Wiggling the dial a tiny bit
can encourage this event. Others, you actually have to backtrack
clockwise a few digits to actuate something internally.

I've had success in contacting the lock manufacturer for instructions,
and alt.locksmithing can certianly set you straight.

Doug White

Doug White

2012-01-20 14:16:07 UTC

Post by Doug White

Post by Ignoramus32441
I purchased this Mosler safe. As you can see, it is open and empty,
http://igor.chudov.com/tmp/Mosler-Safe/
The combination, as written on the masking tape stuck on the safe,
R 63
L 47 3 turns
R 25 2 turns
L to 0
However, the safe would not open. I was once shown that the combo
works, however, I cannot redo it. The safe is still open and I would
like to figure it out.

<snip>

Post by Doug White
I've had success in contacting the lock manufacturer for instructions,
and alt.locksmithing can certianly set you straight.

Sorry, I didn't notice you has already crossposted there.

Doug White

Jay Hennigan

2012-01-20 23:00:45 UTC

Turn the dial to the right at least three complete revolutions.

Stop at 63.

Turn the dial to the left. Stop the THIRD time that you get to 47.

Turn the dial to the right. Stop the SECOND time you get to 25.

Turn the dial to the left. Stop the FIRST time you get to 0.

Then turn the handle and see if it opens. If not, continue to the left
and the dial should stop within a short portion of a revolution. Then
turn the handle to open the safe.

DO NOT CLOSE THE DOOR until you have been able to successfully open it
several times in a row with the door open.

--
Jay Hennigan - CCIE #7880 - Network Engineering - ***@impulse.net
Impulse Internet Service - http://www.impulse.net/
Your local telephone and internet company - 805 884-6323 - WB6RDV

Chrissy

2023-03-16 17:32:26 UTC

I have the same safe do you have to turn first number four times ? Everytime I try it I can't open it. By bf can but I can't any tip

--
For full context, visit https://www.polytechforum.com/metalworking/how-to-open-a-mosler-safe-with-combination-532537-.htm

j***@gmail.com

2014-06-13 13:46:57 UTC

I purchased this Mosler safe. As you can see, it is open and empty, so there is no hanky panky going on: http://igor.chudov.com/tmp/Mosler-Safe/ The combination, as written on the masking tape stuck on the safe, slightly modified to preserve all numbers order, is as follows: R 63 L 47 3 turns R 25 2 turns L to 0 However, the safe would not open. I was once shown that the combo works, however, I cannot redo it. The safe is still open and I would like to figure it out. If anyone can help me, it will be GREATLY appreciated! Thanks, guys! i

when you get to zero, push in on the dial and let go then turn to the right until the dial stops. Pull the handle down and it should open.

g***@gmail.com

2016-11-13 00:37:28 UTC

How to open the safe without no combination

d***@gmail.com

2016-12-08 15:44:15 UTC

Hi could anyone help me?
I have opened my Mosler Safe with the combination, and now I have the internal door to be opened. I have two keys, thin, one longer than the other, but I can't find the way to use them properly and open this second door. Any suggestion?

j***@gmail.com

2017-04-12 15:49:21 UTC

I have a Mosler safe that has a safe inside. I have the combination to the outer safe, but the inner safe, I dont have the combination. However, it is not locked. It is open. How can I discover the combination of the lock?
John

h***@gmail.com

2017-10-24 02:05:17 UTC

Try your numbers 2550 25 or 50 2550 I have a Mosler safe to that has a seat in side from the post office I can get into the safe that's in side but I forgot my combination to the outside and can't find anybody to help me to open it

d***@gmail.com

2017-10-24 03:43:08 UTC

Call a safe tech. Moslers are almost all fairly serious safes, especially any you would find in government use like in a PO. If you really forgot the combination you probably aren't getting in without doing a lot of damage unless you have some expertise.

d***@gmail.com

2017-10-24 03:38:13 UTC

Post by j***@gmail.com
I have a Mosler safe that has a safe inside. I have the combination to the outer safe, but the inner safe, I dont have the combination. However, it is not locked. It is open. How can I discover the combination of the lock?
John

Take the cover off the lock and see what numbers the gates line up under the fence at. If you can't figure it out this way on your own, no amount of instruction is gonna help you. If the lock is Mosler, which is by no means assured, then the wheels probably run in back to front order. The rear most wheel in the pack is dialed first and so on back to front. Most other modern safe locks work the opposite way with the wheels being dialed in order front to back. S&G Ilco, Lagard will all work in the latter manner.

s***@gmail.com

2018-10-01 18:38:48 UTC

At 0 press it and then turn to right and it should lock

J.B. Wood

2018-10-02 10:37:05 UTC